Reasons Your fiat bravo key 500 Key Fob Won't Work

A key fob for the fiat 500x key fob programming 500 is a convenient way to open the doors and start the car. There are many reasons why the fob won't work. This could be due to a dead coin battery water damage, receiver module problems, and interference.

This listing is for a NEW replacement fiat 500 key fob programming Flip Key Remote - like the Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). It includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob that isn't working. Modern key fobs have a limited range of operation and must be within a few inches of the vehicle to function. If you are not within your vehicle and you hit the keyfob, it will not respond, and display the message "Key Fob Not Detected".

If this happens, simply replace the battery on your coin cell (Part number CR2032) with a fresh one from a trusted brand such as Panasonic, Duracell, or Energizer. They can be found in the local hardware store or online.

After you've replaced the battery in the coin cell you can test it by standing close to your Fiat Ducato Key Replacement 500 and pressing the buttons. The parking lights should blink and the key fob will operate the lock and unlock switches.

If the key fob won't work after replacing the battery, it could have water damage that prevents it from communicating with the receiver module inside your car. Water damage can occur in a variety of ways, ranging from the slightest splash to submerging the fob into salt water at the beach. If you think your fob was exposed to water, put it in a rice bag to draw out the moisture. If this doesn't work, your fob is likely to need to be reprogrammed by an experienced auto locksmith or by the dealer.

Water Damage

Water damage can occur when you submerge the fob in the ocean or wash it in a washing machine. Saltwater is especially dangerous to the circuit board of the fob that can cause it to short out and eventually end up dying. It's not good to soak the fob in water however, don't give it up in the event that you accidentally drop it in water or forget to remove it from your pocket.

First, remove the battery from the fob. Clean the electronic chip with isopropyl alcohol or a similar product and then dry it thoroughly before replacing the battery. Check the fob again to verify if it's functioning. If the key isn't working, it may have to be reset. This is usually handled by an auto locksmith or dealer.

If your key is a bit older and has not been programmed for your vehicle You will need to replace it completely. A professional locksmith in the automotive industry can carry out this simple task. The locksmith will need to cut the key to match the ignition of your vehicle. They'll also have to reprogram the fob in your car's system. This is a quick and inexpensive process that can usually be completed on the same day.

Receiver Module Issues

Your 500 key fob might not work because it's out of range. The remote typically has an area of 30 feet or less and if it's far away from your car it won't respond to your commands. You can easily solve this problem by moving the remote closer to your vehicle until it responds.

If your fob doesn't work after you replace the coin battery, also known as a "button", "watch" or "button", it could be due to a problem with the circuit board inside. Reprogramming the fob is usually the solution to this issue. The instructions are available for the majority of vehicles on YouTube or in the owner's guide.

It may be necessary to replace the clips made of metal that hold the coin batteries in their place. If they loose tension, it could hinder the battery from being seated properly and could cause your remote to malfunction.

In rare instances it is possible that the fob will become disconnected from your vehicle due to software problems or hardware issues. It is possible to fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In some instances, they may need to reinstall the program in your body control module, as well.

Interference

Interference can also cause the key fob not to receive or transmit the signal. This may happen if the keyfob is located in close proximity to a radio transmitter, such as a cell phone or radar detector. The key fob could not work due to a bad connection with the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you've tried everything at home to fix it (e.g. You might have a damaged 500 receiver module after you've tried replacing the battery, reprogramming, or using a spare key fob. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It converts the signals into electronic commands that are then interpreted by the vehicle.

There's a quick and easy way to reset the 500's in-board system including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Then reconnect the battery. This will eliminate any residual electricity and restart the car's computers. This can help get your key fob working again. If the problem persists you should speak with an expert technician. They will be able to determine the exact cause of problems.