Reasons Your fiat 500 electric key 500 Key Fob Won't Work

A fiat punto evo key 500 key fob is a handy way to open the doors and begin the car. There are many reasons the fob could stop working. This could be due to a dead battery, water damage, issues with the receiver module, and interference.

This listing is for a NEW replacement key For fiat ducato van Fiat Flip Key Remote - similar to the Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

The most frequent reason that the 500 key fob won't work is the battery is dead. Modern key fobs have a very limited operating range, and must be within only a few feet from the car to operate. If you are far from your vehicle, and you press the keyfob button it will not respond and display the message "Key Fob Not Detected".

If this occurs then replace the battery for your coin-cell (Part Number CR2032) by a fresh one of a reliable brand, like Panasonic Duracell or Energizer. You can find them at the local hardware store or on the internet.

You can test the coin-cell battery by pressing the buttons while you're standing close to your fiat 500 car key cover 500. The car will blink its parking lights, and the key fob should work the lock and unlock switches.

If the key fob doesn't work after replacing the battery, it might be damaged by water, which prevents it from connecting to the receiver module in your vehicle. Water damage can happen in many ways, including an easy splash or submerging the key fob in saltwater at the beach. If you suspect your fob was exposed to water, put it in a dry rice bag to draw the moisture back out. If that doesn't work your fob may need to be reprogrammed by an experienced auto locksmith or the dealer.

Water Damage

The fob does have rubber seals that keep water from the chip's electronic circuit it, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater is particularly dangerous to the fob's circuit board that can cause it to short out and eventually die. Getting the fob wet is not an option, but if you drop it in a cup of water or forget to take it out of your pocket before you run the washer and you don't have a chance, don't give in.

Remove the battery first. Before replacing the battery clean the electronic chip with isopropyl, or a similar product. Check the fob again to see if it is functioning. If the key isn't working, it may have to be reset. This is usually done by an auto locksmith or dealer.

If your key is a bit older and not programmed to work with your vehicle You will need to replace it completely. A professional automotive locksmith can do this job. The locksmith must cut the key to match the ignition of your car. The locksmith will also have to program fiat 500 key fob your fob into the car's system. This is a cheap and quick process that can be completed the same day.

Receiver Module Issues

The 500 key fob you have may not function because it's out of range. The remote has a maximum range of 30 feet, which means if you are too far away from your vehicle it will not respond to your commands. It's easy to solve this problem by moving the remote closer to your vehicle until it responds.

If your fob won't work after you replace the battery for the coin, also called a "button", "watch" or "button" It may be due to a malfunction on the circuit board inside. Reprogramming the fob typically resolves this problem. The instructions are available for the majority of vehicles on YouTube or in the owner's manual.

It is sometimes necessary to replace the metal clips that hold the coin batteries in their place. If they lose tension, it can stop your coin battery from being properly seated, causing your remote to malfunction.

In rare cases, the fob may become desync'd with your vehicle due to software or hardware issues. This can be a major trouble, but you could frequently fix this issue by visiting a local dealer or auto locksmith to reprogram your fob. In certain instances, the software may also require reinstallation into your body control modules.

Interference

In addition to a dead coin battery The key fob might not be able to receive or transmit a signal due to interference. This is possible when the key fob is near the radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. Other reasons the key fob could not function could be due to a weak connection to the buttons or damage to the internal chip or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to resolve it (e.g. You may have a faulty 500 receiver module in the event that you've tried replacing the battery, reprogramming or using a spare fiat 500 key key fob. The receiver module, located beneath the dashboard, picks up radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

Luckily, there is an easy method of resetting every single system on board in your 500, including the key fob. Disconnect the battery for 15 minutes by removing first the negative cable and then the positive cable. Then, reconnect the battery. This will remove any remaining electricity and then restart the car's computer system, which can help you get your key fob working again. If the issue continues, you should seek out an expert technician. They'll be able to identify the root cause of your issues.