How to Replace a Kia Sportage Replacement Key

For a number of kia picanto key fob replacement (Telegra official) models, the key contains an integrated keyless entry system. This key usually resembles a remote control and is able to be replaced by a new one purchased from an kia soul key fob dealer or a locksmith.

Key fobs might stop working for several reasons, including batteries that are dead worn buttons, signal interference, water damage, and a defective receiver module. Here are some tips to help you get your Kia key fob that is a replacement for the sportage again.

How do you replace the remote key or smart key?

Whether your Kia comes with an intelligent key, remote key push-to-start key, or a standard non-transponder key made of metal The battery inside these keys will eventually require replacement. This is especially true if your car displays a message indicating that the smart or remote keys aren't powered.

This is a relatively simple procedure. In order to replace the battery of the key fob, remove the mechanical key from the slit in the back of the key fob. Next, remove the cover. A small screw is inside the key fob, which holds the battery in the correct position. By using a small screwdriver unscrew the screw and remove the old battery. Then, insert the new and close the slit inside the key fob.

When the key fob is equipped with new batteries, test it by pressing the locks and unlock buttons. You're good to go when the doors lock or unlock as expected. You can now use the hands-free lock/unlock feature on your Kia when your fingers start to get cold or you have to do some errands in Brandon.

Note: Some key fobs could need to be programmed (transponder chips or smart keys). This requires a specific programming machine that only the dealer or automotive locksmith can access. Other keys (non-transponder metal keys) do not require programming. If you're looking to reprogramme your key, you'll need record the key code number on the tag for the key code.

How do you replace a dead battery?

If the Kia key fob doesn't respond to pressing the lock/unlock button, it's likely that the battery is low. A low battery may also cause other problems like the check engine light coming on or delayed cranking of the engine. It is relatively easy to replace key fob batteries by using only some tools.

Before beginning the process be sure that your vehicle is off and that all doors are shut. Find the small metal or plastic piece on the bottom of the key fob. Then, jiggle it until the key is released. The key can be put into the door's driver handle to unlock your car.

To replace the key fob battery, take off the rear cover and use a plastic bar tool to remove the latch holding the black negative battery cable. Take the old battery out, and then align the replacement battery to ensure its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid damaging or bending the contacts of the metal.

After you have installed the new battery and turning the key fob on and off in the ignition until the door locks cycle. You can then test your Kia key fob to see whether it's working again.

How to replace the smart key

You can have the standard keyfob or Smart Key based upon the model of Kia Sportage. The smart key has an embedded mechanical key blade, unlike the standard key fob, which does not. Both key fobs contain batteries that eventually require replacement. Fortunately, this is an easy task that takes just two minutes.

Before you begin before you begin, ensure that you are on a flat surface with sufficient lighting and that your Kia is not on. Also, remember that there are tiny components inside the fob that could be removed if not careful.

The release button for the small size is located on the lower backside. It could be a circular silver button or a rectangular slot. When you press it the mechanical key blade will be released and you will be able to open the key fob.

Once you have the key fob open and you are able to take off the old battery and replace it. The new battery is a CR-2032 that can be purchased online or at a local auto parts store. After you're done, your key fob should allow you to lock the vehicle, unlock it, and then start your vehicle, even if it isn't running.

How do I replace the mechanical key

The Kia key fob is a great feature that lets us lock and unlock our car with the press of one button. Like any other device there are issues with it occasionally. Luckily, there are steps to take to troubleshoot these issues and ensure that our key fobs are in good working condition over the long haul.

A dead or weak battery is among the most frequently encountered issues. The fob could be able to stop working altogether or work intermittently. If this is the problem then replace the battery with an entirely new battery.

If this isn't enough to resolve the issue you can try using a standard flat-head screwdriver to break open the fob's plastic casing. Be careful not damage any internal components or scratch the plastic. Once open, carefully remove the old battery and replace it with a new one.

After the new battery has been put in, shut and open the doors using the mechanical key (every Kia fob comes with an emergency mechanical key that will fit in the slot). Test the key fob to make sure it is working correctly. Contact a dealer locksmith to fix the issue when the fob still is not working. To avoid future lockouts, make sure you get an emergency key that can be able to work with all door and trunk cylinders.