Peugeot 208 Key Replacement

It is recommended to leave the replacement of Peugeot 208 keys to auto locksmiths who have the necessary equipment and technical know-how. They can create and program new keys faster than a dealership would and at a lower cost.

A dead coin battery is the most likely cause the reason your key-fob stops locking or unlocking doors. There are other reasons why the key may be malfunctioning.

Dead Coin Battery

A dead coin battery can hinder your Peugeot 208 from locking or unlocking and will not start the engine. In this scenario, you will need to use the alternative starting method as described in your vehicle's owner's manual.

Another reason your 208 might not start is that the spark plugs have been damaged. The spark plugs ignite the fuel to start the engine. They are only able to last for a short time. If they're not used enough they will eventually fail.

There is a straightforward solution to this issue. The best option is to check the voltage of your car battery with a multimeter. If it's below 11.5 Volts, then you need to replace it. If the battery has corroded, it is important to clean its contacts. This can be done by removing the rubber cover from the two battery terminals, and then using a wirebrush, you can remove any corroded battery parts. Then, you should connect your cables to connect the positive and negative poles.

Water Damage

If your 208 will not start and the battery has not fallen flat, it is time to look at the spark plugs. It could be that they're dirty and they don't spark. This can be easily corrected by cleaning the spark plugs in a workshop.

Peugeot cars use transponder keys that is compatible with the car's immobiliser system. This ensures that only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged, then it won't send the correct signal to the vehicle.

Water damage is the most common cause of this problem. This is most common in colder climates where the vehicle might have been exposed to rain or snow. In this case, you need to contact a reputable locksmith who has the tools and equipment required to reprogram the key. They will also have the latest technology and equipment needed to create a Peugeot smart key. The process should not take more than 15 minutes.

Faulty Battery Contacts

Peugeot changed from the carbon-encased transponder chips to a brand new type of chip that relies on electronic components in circuit boards. This new system works great when it's new, however, over time, the circuit boards begin to lose their effectiveness and cease working correctly.

This can stop the immobiliser's function from being activated, meaning your vehicle won't start. Contact an peugeot key replacement specialist or a locksmith, if this is the situation.

A common issue is when the battery inside the key fob starts to die. This causes the blade of the key to stop feeding into the lock. A locksmith from your car will replace peugeot key the battery, and cut a new blade for you. This is a simple fix.

Faulty Receiver Module

If your peugeot key programmer key fob isn't working after dropping it on the floor, or being exposed to a sudden downpour or accidently washing it or washing it, it could be due a malfunctioning receiver module. The receiver module is responsible for transmitting radio frequencies to the onboard computer which regulates the central locking system of your Peugeot vehicle.

The key fob itself is fitted with rubber seals to prevent water from reaching the chip inside. However prolonged exposure to water could cause damage to these seals and the chip. The high salt content in the ocean water or pool could cause damage to the key fob when it is submerged.

If your Peugeot spare key fob isn't working You'll need the module replaced. This can only by done by a Peugeot specialist or expert auto locksmith. Peugeot keys, unlike other cars, are secured by an immobilizer system. This requires the correct codes to start the car. It is for this reason that you should only trust an authorized Peugeot locksmith to create and program an alternative.

Computer malfunctioning on-board

The on-board computer in your Peugeot is responsible for a variety of systems inside your car, including power windows and airbags. The on-board computer will display an error code when something goes wrong. The code will be stored within the system until the issue is fixed. Most often, this involves the on-board computer being replaced.

One of the most common causes of the airbag light turning on is the loose or corroded connectors in the airbag sensor. This can be caused by wear and tear, aging or exposure to moisture and salt. This issue needs to be taken care of as soon as you can, since an airbag that is not functioning could pose danger in the event of an accident.

If your peugeot 307 key fob is showing a card that is not being detected error, the battery inside the key fob could be weak or dead. This will stop the key fob from sending a signal to deactivate your vehicle's immobilizer. Try this by pressing the unlock button on the fob's key and then trying to start your vehicle. If this does not work, the key battery has to be replaced.