UPVC Window Repairs

uPVC windows are energy efficient and can help reduce heating costs. However, as they age problems can arise which need repair. This could include damaged hinges, handles or locks.

DIY people can fix wooden windows with ease. It can also be cheaper than a new replacement window.

Cracks

Cracks and tears in uPVC windows could be a major issue. If windows are not properly repaired, they can result in water intrusion and less effective barriers to cold weather, and even structural damage. It is important to find a local builder or repair service that specialises in the repair of uPVC frames and can demonstrate the skills, experience and tools needed to produce the best results. This will ensure your crack is repaired swiftly before it gets worse and you don't need to replace your window unit or glass.

There are many home-based solutions that can be used to repair small cracks in glass. Masking tape and superglue are two of the most common products to hold cracked glass in position for a short time. For cracks that are more extensive, the tape may need to extend past the crack on both sides for best results.

Another option is two-part epoxy that can be used to fix broken or cracked glass. This is available from most hardware stores and can be bought at a cost of around $10. Ensure that your workspace is prepared prior to mixing the epoxy and make sure you have the correct tool for the job, such as a soldering iron.

If you notice that your upper or lower sash has difficulty raising it is most likely due to the cords that connect to the sashweights are damaged. This is a simple fix that can be accomplished with a ladder and flathead screwdriver. A drip cap that is rotten can be easily replaced at home. Rot-free drip caps are available at a majority of home centers and can be nailed or caulked into place with ease. Check that the glass of a triple- or double-paned window isn't cracked. This is because the gasses that fill the space between the panes are responsible for enhancing energy efficiency. They should be retained, not escaping.

Water Leaks

If your uPVC window is leaking, this can ruin your interior and cause costly repairs. Water leaks can also cause structural damage to your home and the growth of mold. It is crucial to address any issues caused by leaky windows right away to minimize the damage.

One common cause of window leaks is a damaged sealant around the frame. Silicone caulking can restore the seal to its original condition and stop leakage. Look for gaps and cracks around the window frame, and also the stone or brick wall surrounding your windows.

A blocked drainage hole or an issue with flashing are the other two typical causes of windows that leak. It is important to ensure that the drainage holes are free and unclogged, especially during heavy rainstorms. Also, you should look at the flashing around your window to ensure that it is properly sealed.

Finally, it's essential to ensure that your drip cap isn't broken or rotten. A rotted drip cap or one that's missing can allow water from above to seep into your window and cause structural damage. Replacing the drip cap isn't a complicated job and usually a straightforward process of buying a new one and nailing it into the right spot.

It's recommended to have your windows tested for water-tightness by a qualified. They can employ a specific tool to measure the water-tightness and strength of your windows and make sure they are in line with industry standards. If your windows fail the test, they will require replacement. This is a cost-effective repair however it's worth it for the comfort and safety of your family.

Sagging

If your windows do not close properly, it can lead to a number issues including drafts, condensation and a rise in your energy bills. It can be a sign that the windows weren't well fitted at installation or the sealant has stopped working. Fortunately, there are a few things you can do to correct the issue.

To repair your window correctly, you need to set up a workspace that is well-lit. Begin by laying newspaper or an old blanket on the floor to protect it from any drips or splinters that may come from the window while you work.

Use a white cloth soaked in a solution of detergent and water. This will ensure that you don't leave any stains of color on your windows. Mark the the hinge channel on your upvc window repairs near me window when you are ready to start working. Then, remove the channel from the frame and fill the screw holes with epoxy (for uPVC windows) or wood filler (if your frames are constructed from wood). Make sure you scrape the hole you have filled before it sets.

After the holes have been filled, you can install the hinge channel. Be sure to center it on the window jamb, and then drill the new screw holes about a quarter-inch away from the original locations.

Then, take a measurement of the length of the spindle that protrudes from the underside of your handle and then order an alternative online or window repairs bring the old one to the hardware store to purchase a new. Then, take out the setscrew on the shaft of the operator and file it flat so the set screw will be secured to the shaft (photo). Now, your uPVC window should be closing smoothly.

Broken Hinges

You will have difficulty opening or closing your uPVC windows if the hinges are broken or not working correctly. This could cause an issue with security and stop your home from remaining cool or warm. It's simple to purchase a new window hinge for your uPVC windows. It's important that you use the right hinge for your windows.

This is because the hinges must be the same size to fit into the window frame. The most common hinge for uPVC windows is standard 18mm or UPVC 15mm window hinges. There are also specialised hinges for wooden frames. The right type of hinge can help you avoid common issues with your windows.

Your window hinges could be stiff or loose due to a variety of reasons. The most common reason is that the hinges are not tightened enough. To check this, use an electric screwdriver to locate the friction screw on the end of the hinge. Then loosen it. Then, you can adjust it by turning it either way.

Contact Preston Glass Fix if your UPVC window's hinges aren't functioning correctly. We can provide an immediate solution. Our technicians will inspect the condition of your hinges and Window Repairs offer you advice on the best solution. We can replace your window hinges, adjust them or install new locking mechanisms to ensure that your UPVC windows are secure and safe for years to come.

The locks are not working properly

UPVC window mechanisms and locks are a crucial part of home security. They make it extremely difficult to open windows without breaking into the home. When a lock fails it can be frustrating, but it's an simple fix and you don't need to replace the entire window.

Sometimes, the issue is a minor issue that could have been prevented if you have had regular maintenance. This is why we suggest having your uPVC windows checked regularly by our annual maintenance program to minimize the risk of issues.

Modern upvc window repair windows come with espagnolette locks. They work by pushing the nose end of the handle on a wedge block, and then turning it to close the lock. They are efficient in locking the window, but should they not be maintained in a timely manner, they may start to fail. We recommend lubricating them with WD-40 a few times per year.

If you notice your uPVC window isn't opening or closing as smoothly as it did in the past, or when the lock isn't working properly, there could be an issue with the locking gearboxes within the frame. Accessing this can be tricky as it requires the removing of the seals that surround the frame and removing the handle (be cautious not to damage the seals).

A locksmith who specializes in UPVC repairs is able to identify the problem quickly and then be able replace the failed locking gearbox with a precise replacement. This quick and easy fix could save you hundreds by avoiding having to purchase new windows.